Kitchen roll\/cloth for drying<\/li>\n<\/ul>\n\n\n\nRemove your filter from your cooker hood and spray on the degreaser. You may want to place it over your sink to this to prevent your worktop from getting covered in grease and grime.<\/p>\n\n\n\n
Leave the degreaser to break down the residue for approximately 10 minutes, as recommended in the accompanying usage instructions. Once it’s done, rinse out your metal filter with hot water to remove all the grease. If your metal filter is dishwasher-safe, you can also run it through your dishwasher for an extra clean finish. <\/p>\n\n\n\n
Note that aluminium cooker hood filters are not recommended for cleaning inside a dishwasher, so double-check if you have any doubts. <\/p>\n\n\n\n
Once your metal filter is sparkling clean and free from greasy residue, please give it a good dry with some paper towels or lint-free cloth, and then let it air dry. Don’t apply heat to your filter, as this could affect its integrity. With your metal hood filter clean and ready to go, or your replacement lined up, it’s time to move on to step 2 before replacing it inside your hood. <\/p>\n\n\n\n
Step 2: Cleaning Inside the Cooker Hood<\/h3>\n\n\n\n There is little point in replacing your filter with a nice clean one if you don’t take the time to remove the built-up grease<\/strong> from inside your cooker hood. If you regularly clean your extractor or it’s a brand new model that you’ve only had for a short period, this step can be just a simple wipe-over with a damp cloth or kitchen roll.<\/p>\n\n\n\nIn most cases, though, you’ll want to take your degreaser and spray it on to make wiping off grease extra easy. For large grease accumulations, leave your degreaser for 10 minutes so that it can get to work. In this case, we recommend placing a kitchen roll, a newspaper, or old clothes under your hood to catch the drips.<\/p>\n\n\n\n
You’ll also want to take care that no grease or cleaning products enter the motor. If you struggle to get into the corners, use a soft toothbrush to scrub hard-to-reach spots in the interior gently.<\/p>\n\n\n\n
Don’t have any degreaser to hand? You can also try mixing the bicarbonate of soda in boiling water. Allow it to cool so it’s hot but not too hot to handle. Use a sponge or a micro-fibre cloth to apply the solution, taking care to avoid getting the motor wet. You may need a little more elbow grease than a chemical product for degreasing.<\/p>\n\n\n\n
However, unless your hood is in desperate need of a deep clean, you should still get great results with a little hard work.<\/p>\n\n\n\n
Before moving on to cleaning your hob exterior, make sure that you have rinsed off all traces of cleaner and wiped your hood interior dry with kitchen paper or a soft cloth.<\/p>\n\n\n\n
Step 3: Cleaning the Exterior<\/h3>\n\n\n\n <\/figure>\n\n\n\nWhile your extractor hood surface is not likely to be as grease-laden as the interior, it can still get pretty sticky with a film of grease, food stains and fingerprints. Therefore, you’ll have to ensure that your cleaning methods are not over-aggressive when cleaning your cooker hood exterior. Otherwise, you’ll risk damaging the surface of your hob, which will detract from its looks.<\/p>\n\n\n\n
Either use a special stainless steel cleaner or make up a paste from one part bicarbonate of soda to one part white vinegar to gently wash your cooker hood. You can use a spray or apply it with a soft sponge. Before you start cleaning, take a few moments to closely inspect your hood to work out the direction of the metal “grain”.<\/p>\n\n\n\n
Looking closely at the metal, you should be able to see miniature grooves in the metal. Therefore, when cleaning the exterior, you will want to clean in a linear motion along the grain, not in circles. Cleaning in this manner will allow you to effectively remove grime and grease build-up inside these tiny crevices, as well as improve your appliance’s shine.<\/p>\n\n\n\n
Bear in mind that the metal on cooker hoods may have different grains, so don’t forget to change direction as you change sides if necessary. While cleaning your stainless steel hood, remove the light cover and leave it soak in hot soapy water. If necessary, remove any stubborn sticky grease with a soft-bristled toothbrush or gentle cleaning pad. Please don’t use anything too abrasive, as it could scratch the surface.<\/p>\n\n\n\n
Replace your clean and dried light bulb casing<\/strong> and proceed to buff your hood exterior to a sheen with a soft cloth in the direction of the grain.<\/p>\n\n\n\nStainless Steel Hood Cleaning Tips<\/h2>\n\n\n\n Here are some other cleaning tips that will come in handy once you do the work.<\/p>\n\n\n\n